Geotechnical Investigation
A geotechnical investigation is the foundation of every well-engineered project — literally. It characterises what is below the surface so that foundations, shoring, drainage, and slope designs are based on measured site data, not assumptions. In Metro Vancouver, with variable alluvial soils, high seismicity, and tight urban lots, a rigorous investigation is rarely optional.
What a geotechnical investigation actually involves
We design each investigation program around your specific site and project type — not a generic template. That starts with a desktop study of available geologic mapping, well records, and previous investigation reports, followed by a site visit to identify soil and groundwater indicators before a single borehole is drilled.
Drilling programs typically combine rotary or hollow-stem auger boreholes with CPT/CPTu soundings where soil conditions allow. In-situ testing — SPT N-values, vane shear, or pressuremeter — is selected to match the design parameters required. Representative samples go to the laboratory for classification, consolidation, shear strength, and other project-specific tests.
The Geotechnical Investigation Report (GIR) interprets the findings and provides the design parameters, foundation recommendations, and construction considerations your structural and civil engineers need to proceed. EGBC and APEGA practice standards are followed for all work in BC and Alberta respectively.
Typical Project Types
- →Residential development & renovation
- →Multi-family & mixed-use buildings
- →Commercial & industrial structures
- →Underground parkades & podiums
- →Infrastructure & municipal projects
- →Seismic upgrade assessments
You write directly to the engineer. Every inquiry is reviewed and responded to by Farshid Bateni, P.Eng., Ph.D. — not a project coordinator or junior staff member.
What is included
Each investigation program is scoped to match your project requirements. The following represent the full range of services available under G.01.
- Desktop study: geology, well records, prior reports
- Site reconnaissance & soil/groundwater indicators
- Borehole drilling & continuous soil sampling
- CPT / CPTu with pore-pressure dissipation
- Standard Penetration Test (SPT N-values)
- Field vane shear & pressuremeter testing
- Groundwater depth measurement & standpipe piezometers
- Laboratory testing: grain size, Atterberg limits, consolidation, shear strength
- Liquefaction susceptibility & triggering analysis
- Seismic site classification per NBCC
- Bearing capacity & settlement analysis
- Formal Geotechnical Investigation Report (GIR)
From site visit to sealed report
Most investigations move through four phases. Timeline from brief to draft report typically ranges from three to six weeks depending on drilling contractor availability and laboratory turnaround.
-
01
Brief & program design
We review your project drawings, site plan, and structural loads. If a preliminary geotechnical assessment or prior borehole data exists, we use it. We then design a borehole and testing program sized to the risks and regulatory requirements of your project — including the number and depth of boreholes, CPT soundings, and in-situ test types.
-
02
Field work
We coordinate drilling contractors, attend the site during drilling operations, log all boreholes in real time, select samples for laboratory testing, and conduct in-situ testing. Groundwater levels are measured in open standpipes or piezometers and re-read at a later date to capture any dynamic response.
-
03
Laboratory testing
Representative samples are submitted to an accredited geotechnical laboratory for classification, index property, consolidation, and shear-strength testing. We review laboratory data as it is received and flag any results that warrant supplemental field sampling or testing.
-
04
Geotechnical Investigation Report
We interpret the field and laboratory data, prepare subsurface profiles, conduct analyses (bearing capacity, settlement, liquefaction, seismic site class), and write the GIR. The report includes all original borehole logs, lab data sheets, and a site plan. The sealed and signed document is suitable for submission to the building department, structural engineer, and lender.
What you receive
The GIR is a signed and sealed engineering document suitable for permit submission. It typically includes:
- Signed & sealed Geotechnical Investigation Report (PDF)
- Site plan with borehole and CPT locations
- Borehole logs to ASTM / USCS classification standards
- Subsurface soil profile cross-sections
- Laboratory test data sheets
- Foundation type recommendations with allowable bearing pressures
- Estimated settlements under service loads
- Liquefaction analysis (if seismic hazard warrants)
- Seismic site classification (NBCC Site Class, Ta, Sa)
- Groundwater conditions & drainage recommendations
- Construction-phase considerations & monitoring recommendations
- Draft available for structural engineer review prior to final issue
The investigation informs everything that follows
The GIR is the starting point. These services typically follow and draw directly on the investigation data.